ArcMeister AC Ballast


	ArcMeister Lamps
	High-Output
	High-CRI
	High Stability
	Ballast
	AC
	DC
	Exterior
	FGM Technology
	Fiber Box PTX-60
	Lamp Comparison
	TechnoLab GmbH is exclusive PEC Lamp distributor for Europe

	TechnoLab GmbH Am Borsigturm 46 13507 Berlin Tel:(030)43033160 Fax:(030)43033169

Green Energy Lighting Corp 11266 Monarch St. Garden Grove, CA 92841 Ph:800-211-5483 Fx:714-889-4128

Universal 90V-264V AC

Dimmable Range 40W-80W

Instant Start at 90% light in 90 sec.

Hot re-strike in 45 sec.

Download Datasheet


1. Application
	This specification shall apply to the lamp driver M66WBU-M to operate a ArcMeister™ 60W lamp. This driver is designed and adjusted for the metal halide lamp.
2. Standard Applied
	The lamp driver is designed to meet these standards when mounted in the set.
[2-1] Safety Standard
	UL60950, IEC60950
[2-2] EMI
	FCC Part18 class B

Note: This product is capable to restrike itself in 45 sec. however, it is not recommended that you re-start the ballast while the lamp is still warmed up, as it will cause the electrode to wear out and as a result, it will shorten the life of the lamps. The most ideal re-stike time in order to maintain the lamp life is 45 sec. or longer.

3. General Specification

Category	Specification	Remarks
Cooling Method	Self-Cooling System under 60W Forced Air Cooling recomended for over 60W.
Operation Ambient Temperature	0°C - 60°C (32F-140F)
Operational Relative Humidity	10-80%RH	no condensation
Storage Ambient Temperature	-20°C - 70°C (60F-158F)
Storage Relative Humidity	5-90%RH	no condensation

4. Electrical Characteristics to Operate 60W
[4-1] INPUTS

Category	Specification	Remarks
Rated Input Voltage	AC100-240V	Frequency 50-60Hz
Input Voltage Range	AC90-264V	Frequency 48-62Hz
Input Power	80W ± 5%
Input Current	1.0A	at AC 100W

[4-2] OUTPUTS

Category		Specification	Remarks
Output Power of BT	Vs inputs	60W ± 5%	Vin = AC90-264V (VL=55V)
Output Power of BT	Vs output	60W ± 5%	VL=45-100V
Peak Voltage during ignition		10-20kV	Vin = AC90-264V
Cycle of HV during ignition		60 cycle	Vin=AC100V
Ignition time		below 2 Seconds	Vin=AC100V
Power Control Range		60W ± 25%	By internal VR
		40W ± 5W	By external VR (min)
		80W ± 8W	By external VR (max)
		40W ± 5W	By power control signal (0V)
		80W ± 8W	By power control signal (5V)
DC Fan Output		11.3-12.7V	IF=0.25A (max)

4. Reliability

[8-1]	MTBF (Mean Time Between Failure) : 10,000 h and more
	MTTF (Mean Time to Failure): 50,000 h

Operating Condition
Ambient Temperature: 60°C (140°F), input voltage: 100V AC 50Hz

[8-2] Environment of Examination
After the following environment examination, in the normal operating temperature.

Electrical Characteristics

Test	Condition
High Temperature Operation Test (Tested 200hrs)	Ambient Temperature: 60°C (140°F)
	Input: AC90V 50Hz
	Load: 80W
Low Temperature Operation Test (Tested 96hrs)	Ambient Temperature: 40°C (104°F)
	Input: AC90V 50Hz
	Load: 80W
High Temperature & High Humidity Operating Test (Tested 96hrs)	Ambient Temperature: 40°C, Humidity: 95%RH
	Input: AC90V 50Hz
	Load: 80W
High Temperature Stability (Tested 96hrs)	Ambient Temperature: 80°C (176°F)
Low Temperature Stability (Tested 96hrs)	Abient Temperature: -20°C (-4°F)
High Temperature & High Humidity Stability (Tested 200hrs)	Abient Temperature: 40°C (104°F)
Thermal Shock (Tested 10 cycles)	Ambient Temperature: -20°C/30Min to 70°C/30Min. Temperature rise/fall within 5Min. to next temperature
Cyclic Temperature Operation (Tested 10000 cycles)	Ambient Temperature: 25°C (77°F)
	Input: 90V AC 50Hz
	Load: 80W, ON/2Min OFF/5Min
Vibrations (Tested 1hr each for 3 directions X,Y, and Z)	Acceleration: 1.96m/S2 (constant)
	Frequency Range: 10-55Hz
	Directions: 3 (XYZ)
Shock (Ballast fixed on wooden board)	Tested the intensity when dropped above 1.18 inch from ground