 |
M66C18 - High Lumen Output HID (Type M)
1.5mm Arc Gap
High Lumen Lamp is aimed more towards
the professional fibre optics business, where getting the maximum quantity of
light into the fibres is of paramount importance. It's based on a pure mercury
discharge operating at ultra-high pressure, which allows its arc to be reduced
to the tiniest dimensions. It succeeeds in concentrating much more light into
the centre of the beam, and here it really scores highly on projecting a large
percentage of its light into optical fibres. However, its colour rendering index
drops down into the 30s, so it's not really a lamp for general lighting work.
Despite this, when the application is simply for direct viewing of fibre tails,
for instance in a starlight ceiling or for outlining architectural detal, its
ultra bright crisp white beam achieves stunning effects
Download Datasheet
|
| 1. General Specification |
|
Category |
Standard Rating |
Frequency |
Numbers per Inspection |
Method |
| Wattage |
60W |
|
|
|
| Dimmer Range |
40W±80W |
|
|
|
|
Voltage |
60V±15V |
per lot |
1 /Charge (min. 1 / 20St)
|
Power Meter
|
| Initial Lumen |
4000lm±1000lm |
per lot |
1 /Charge (min. 1 / 20St)
|
Spectrometer |
| Light
Flickering |
less than 5% |
per lot |
1 /Charge (min. 1 / 40St)
|
Measured the light from fiber Φ 8mm x 300mm.
Operating position: perpendicular
Measured for 10 min. after 5 min. of
operation. |
| Warm-Up Time |
60sec |
per lot |
1 /Charge (min. 1 / 40St)
|
Measured when lumen reaches 80%
|
| Color Temperature
|
6500K±1500K |
per lot |
1 /Charge (min. 1 / 40St)
|
Measured the light from fiber Φ 8mm x
300mm
|
| CRI |
85K±10(Ra) |
|
|
Measured the light from fiber Φ 8mm x
300mm
|
| Avg. Life* |
4000 h |
|
|
| |
| |
|
*Avg. Life.: Rating is the point where lumen reaches 50% of the initial lumen.
|
| |
| |
| |
| 2. Working distance |
 |
|
* Working Distance (WD) is defined as the distance from surface of the reflector,
where the light comes out, to the fiber source. Working Distance is set to 40mm
which is the most ideal distance in order to get a maximum lumen output at the
other end of the fiber souce.
|
|
| 3.
Operating Condition |
| Category |
Operating Condition |
Remarks |
|
Operating Position |
Perpendicular, allowing ±90° toward lighting
direction
|
Lumen and Lumen Stability may drop 0-10% due to
slight tilt
|
|
Operating Environment (Temperature )
|
0°C-60°C (32 F - 140 F) |
|
| Warm-Up Time |
60 sec+ |
Re-strike may fail when turned on in less than 45
sec.
|
|
| |
| 4.
Reliability Test |
| Category |
Operating Condition |
Remarks |
|
Working Condition Under High Temperature &
High Humidity
|
Ambient Temperature: 40°C (104
F) |
|
| Ambient Humidity: 80% RH |
| Wattage: 100W (Standard +
40W) |
|
Storing Temperature (Extreme High)
|
Ambient Temperature: 80°C (176
F)
|
|
| Stored for 100 h |
|
Storing Temperature (Extreme Low)
| Ambient Temperature: -20°C (-4
F)
|
|
| Stored for 100 h |
|
Turned ON/OFF Intermittently
|
Ambient Temperature: Room
Temperature
|
- |
| Ambient Humidity: Average |
|
Shock Test |
Dropped from 31.5 in. from the floor
|
- |
|
Tested on each dimension
|
|
Tested 10 times on concrete and linonium
|
| Vibrations
Test |
Lamp directly attached to Vibration Testing
Machine
|
- |
| 10G 5-500Hz 7.5min
| |
| |
| 5.
Warranty |
|
Warranty Period: 400 hrs of operating
period or 6 months from the date of purchase.
PEC LAMP will repair/replace defective item(s) within our
warranty and/or PEC LAMP's extended warranty period (if applicable). For PEC
LAMP's warranty to be in effect, product must have been used for it's inteded
purpose through normal use. Defects which result from negligence, misuse, or
accidents or if product is determined by one of our technicians that it was
misused will not be covered under warranty. Due to PEC LAMP's requrements and
return guidelines, all products being returned for warranty or reselection
purposes must include manuals, cables, and packaging in its original condition.
We reserve the right to make all final decisions on repairs or exchanges.
|
|
| |
| | | |
Contact
